Тема: Жесткий диск Seagate 3,5 2 TB 2 шт.
1
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST2000DM001-1CH164
Serial Number: W1E2DT6M
LU WWN Device Id: 5 000c50 05dc9f5c6
Firmware Version: CC24
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Oct 24 13:55:12 2016 NOVT==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/e … Q/207931en
http://knowledge.seagate.com/articles/e … Q/223651enSMART support is: Available - device has SMART capability.
SMART support is: Enabled=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 232) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 091 086 006 Pre-fail Always - 126137844
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 177
5 Reallocated_Sector_Ct 0x0033 083 083 010 Pre-fail Always - 22000
7 Seek_Error_Rate 0x000f 074 060 030 Pre-fail Always - 17291218162
9 Power_On_Hours 0x0032 070 070 000 Old_age Always - 27053
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 179
183 Runtime_Bad_Block 0x0032 098 098 000 Old_age Always - 2
184 End-to-End_Error 0x0032 060 060 099 Old_age Always FAILING_NOW 40
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 849
188 Command_Timeout 0x0032 100 087 000 Old_age Always - 15 26 35
189 High_Fly_Writes 0x003a 092 092 000 Old_age Always - 8
190 Airflow_Temperature_Cel 0x0022 067 054 045 Old_age Always - 33 (Min/Max 1/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 94
193 Load_Cycle_Count 0x0032 042 042 000 Old_age Always - 116750
194 Temperature_Celsius 0x0022 033 046 000 Old_age Always - 33 (128 0 0 0 0)
197 Current_Pending_Sector 0x0012 087 087 000 Old_age Always - 2272
198 Offline_Uncorrectable 0x0010 087 087 000 Old_age Offline - 2272
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 21237h+32m+00.156s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 21668285887
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 214175636244
2
[root@xenserver-xpyovkmp ~]# smartctl -a /dev/sdf
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.10.0+10] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST2000DM001-1CH164
Serial Number: W1E2JPZ8
LU WWN Device Id: 5 000c50 05dc9e4ac
Firmware Version: CC24
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Oct 24 14:22:01 2016 NOVT==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/e … Q/207931en
http://knowledge.seagate.com/articles/e … Q/223651enSMART support is: Available - device has SMART capability.
SMART support is: Enabled=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSEDGeneral SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 224) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 096 089 006 Pre-fail Always - 103156185
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 177
5 Reallocated_Sector_Ct 0x0033 082 082 010 Pre-fail Always - 23208
7 Seek_Error_Rate 0x000f 074 060 030 Pre-fail Always - 21623620192
9 Power_On_Hours 0x0032 068 068 000 Old_age Always - 28434
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 179
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 346
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 0 0 1
189 High_Fly_Writes 0x003a 091 091 000 Old_age Always - 9
190 Airflow_Temperature_Cel 0x0022 068 054 045 Old_age Always - 32 (Min/Max 32/32)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 91
193 Load_Cycle_Count 0x0032 045 045 000 Old_age Always - 110328
194 Temperature_Celsius 0x0022 032 046 000 Old_age Always - 32 (0 21 0 0 0)
197 Current_Pending_Sector 0x0012 097 097 000 Old_age Always - 496
198 Offline_Uncorrectable 0x0010 097 097 000 Old_age Offline - 496
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 23263h+40m+48.840s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 20065514602
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 226089407710SMART Error Log Version: 1
ATA Error Count: 346 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.Error 346 occurred at disk power-on lifetime: 28413 hours (1183 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 09:38:44.470 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 09:38:44.470 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 09:38:44.470 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 09:38:44.470 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 09:38:44.470 READ FPDMA QUEUEDError 345 occurred at disk power-on lifetime: 28411 hours (1183 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 07:03:03.073 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 07:03:03.073 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 07:03:03.073 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 07:03:03.073 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 07:03:03.073 READ FPDMA QUEUEDError 344 occurred at disk power-on lifetime: 28410 hours (1183 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 06:42:56.096 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:42:56.096 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:42:56.096 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:42:56.096 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:42:56.096 READ FPDMA QUEUEDError 343 occurred at disk power-on lifetime: 28410 hours (1183 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 06:16:50.479 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:16:50.479 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:16:50.479 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:16:50.479 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:16:50.479 READ FPDMA QUEUEDError 342 occurred at disk power-on lifetime: 28410 hours (1183 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 80 ff ff ff 4f 00 06:06:37.057 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:06:37.056 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:06:37.056 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:06:37.056 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 06:06:37.056 READ FPDMA QUEUEDSMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Старт: 500 р.
Шаг кратно 10 р.
Блиц: нет
Окончание через 48 часов.
Забирать пл. октября - ж/д вокзал
960 936 6881